|
Home > Europe > Fluid Products > Cutting & Grinding Fluids 
|
Soluble Oils
Soluble oils
are suspensions of oil droplets in water made possible by blending the oil with emulsifying and blending agents. An emulsion will have a milky appearance with an oil droplet size in the range 0.005mm (0.0002") to 0.002mm (0.00008"). They provide good cooling with moderate lubricity.
|
 |
TRIM SOL® sf
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® SOL SF is a very high lubricity soluble oil which is suitable for machining and grinding a broad range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining of difficult materials such as stainless steel, inconel and titanium.
- A very universal product that works well in a wide range of operations.
- Compatible with aluminium, all steels and yellow metals.
- Tried and tested extreme pressure (EP) additive controls built-up edge in tough operations.
- Hard water tolerant.
- Fine soluble oil emulsion reduces carry-off for low total operating cost.
- Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures.
- Siloxane free.
- Easily recycled or disposed of without special handling or equipment.
|
|
TRIM® E705
Cutting and Grinding fluid
|
|
|
TRIM® E705 is a high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials but is particularly suited to machining of magnesium alloys. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM® E705 makes it a first choice for high-quality, consistent parts manufacturing
- Very stable formula provides long operational life with consistent performance.
- Extremely hard water tolerant – no emulsion separation even with very high Mg2+ concentration.
- Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE).
- Extremely fine soluble oil emulsion reduces carryoff for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention.
- Compatible with aluminium alloys, steel alloys, cast iron, yellow metals and magnesium.
- Easily recycled or disposed of without special handling or equipment.
- Will run effectively for long periods without the need for costly additives.
|
|
TRIM® E708
Cutting and Grinding fluid
|
|
|
TRIM® E708 is a high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM® E708 makes it a first choice for high-quality, consistent parts manufacturing.
- Very stable formula provides long operational life with consistent performance.
- Extremely hard water tolerant.
- Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE).
- Extremely fine soluble oil emulsion reduces carryoff for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion
prevention.
- Compatible with aluminium alloys, steel alloys, cast iron and yellow metals.
- Easily recycled or disposed of without special handling or equipment.
- Will run effectively for long periods without the need for costly additives.
|
|
TRIM® E715
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® E715 is a high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM® E715 makes it a first choice for high-quality, consistent parts manufacturing.
- Very stable formula provides long operational life with consistent performance.
- Formaldehyde donor biocide free.
- Extremely hard water tolerant.
- Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge(BUE.
- Extremely fine soluble oil emulsion reduces carryoff for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention.
- Compatible with aluminium alloys, steel alloys, cast iron and yellow metals.
- Easily recycled or disposed of without special handling or equipment.
- Will run effectively for long periods without the need for costly additives.
|
|
TRIM® E805
Universal Soluble Oil
|
|
|
TRIM® E805 is a high quality, high lubricity, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. The stable and predictable performance of TRIM® E805 makes it a first choice for high-quality, consistent parts manufacturing.
- Very stable formula provides long operational life with consistent performance.
- Extremely hard water tolerant.
- Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials.
- Extremely fine soluble oil emulsion reduces carryoff for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention.
- Compatible with aluminium alloys, steel alloys, cast iron and yellow metals.
- Easily recycled or disposed of without special handling or equipment.
- Will run effectively for long periods without the need for costly additives.
|
|
TRIM® E905
High-lubricity Emulsion
|
|
|
TRIM® E905 is a high quality, high lubricity, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. The stable and predictable performance of E905 makes it a first choice for high-quality, consistent parts manufacturing.
- Very stable formula provides long operational life with consistent performance
- Extremely hard water tolerant
- Tried and tested extreme pressure (EP) additive controls built-up edge (BUE) in tough operations
- Very wide application range. Suitable for both grinding and machining
- Fine particle size emulsion reduces carryoff and facilitates getting the fluid to the point of cut
- In high-speed turning and milling, E905 has the right balance of cooling and lubrication to provide good tool life and surface finishes
- Compatible with aluminium, steel alloys, cast iron and yellow metals
- Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
- Coolant is easily removed with water, working solution or aqueous cleaners
- Easy recycling or disposal with conventional techniques and equipment
- Does not contain or test positive for phenol
- Will run effectively for long periods without the need for costly additives.
|
|
TRIM® E909
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® E909 is a high lubricity universal soluble oil which requires minimal maintenance in even the most
demanding fluid management systems. TRIM® E909 has broad application in machining and grinding of a
broad range of materials. The high levels of both chemical and mechanical lubricity in this product handle the
tough machining and grinding jobs. The stable and predictable performance of TRIM® E909 makes it a first
choice for high quality, consistent parts manufacturing.
- A very universal product that works well in a wide range of operations.
- Compatible with aluminium, all steels, yellow metals and cast iron.
- Tried and tested extreme pressure (EP) additive controls built-up edge in tough operations.
- Hard water tolerant.
- Low foam even at high pressures.
- Fine soluble oil emulsion reduces carry-off for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion
prevention.
- Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures.
- Easily recycled or disposed of without special handling or equipment.
|
|
TRIM® E925
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® E925 is a revolutionary hybrid soluble oil based on a unique blend of mineral oil based and vegetable ester based additives. Vegetable ester technology gives TRIM E925 extremely high cutting performance without using traditional chlorinated or sulphurised EP additives. This “green” environmental profile is further enhanced by the fact that TRIM E925 does not contain boron or formaldehyde donor compounds. TRIM E925 is a proven, superior product for machining high strength steels, stainless steels, aluminium and corrosion resistant aerospace alloys.
- Extremely high levels of lubrication without chlorinated or sulphurised EP additives.
- Compatible with aluminium, all steels, yellow metals and cast iron.
- Extremely hard water tolerant.
- Low foam even at high pressures.
- Fine soluble oil emulsion reduces carry-off for low total operating cost.
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion
prevention.
- No aggressive biocides.
- Easily recycled or disposed of without special handling or equipment.
- Contains no DEA, boron, chlorine, sulphur, nitrites, formaldehyde donors, or phenolic compounds.
|
|
TRIM® VHP® E820
Cutting and Grinding FLuid Concentrate
|
|
|
VHP® E820 is an aerospace approved, low to no foam chlorine free soluble oil. It is ideally suited for those
operations that utilize high-pressure, high-volume coolant. VHP® E820 is a fluid that will allow you to get
maximum benefits from high velocity through-the-tool coolant delivery systems on VMCs and HMCs and will
assist in achieving maximum productivity from creep feed and VIPER grinders. While VHP® E820 is very stable
and operator “friendly”, its greatest strength comes from its ability to help you get the job done. It is compatible
will all metals and many non-metallic materials as well. Even with a product as “gutsy” as VHP® E820 it will run
for extended periods of time without additives and do so in a very clean manner.
- A very versatile product that works well in a wide range of operations such as production, creep feed
grinding and milling, turning, drilling, and tapping
- Proven performer in difficult creep feed grinding operations
- Fine soluble oil emulsion reduces carry-off for low total operating cost
- Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion
prevention
- Very low foam, without the use of conventional defoamers
- Easily recycled or disposed of without special handling or equipment
- Contains no DEA, boron, chlorine, nitrites, formaldehyde donors, or phenolic compounds
|
|
|
Aerospace
