|
Home > Europe > Fluid Products > Cutting & Grinding Fluids 
|
Synthetics
A true solution
synthetic fluid will be clear with a particle size of less than 0.000001mm (0.00000004"). It will be an excellent coolant but will have no
lubricity. It will typically have hard water tolerance.
A surface
active synthetic fluid will be translucent to clear. It will contain wetting
agents, which lower the surface tension of the fluid and enhance the lubricity.
It will have good rust inhibiting properties, and although it will have
a tendency to foam, this should not present a major concern.
|
 |
TRIM® 229
Straight Chemical Concentrate
|
|
|
TRIM® 229 is a synthetic coolant concentrate. It delivers maximum chemical rust protection on ferrous materials with no residual film and at the lowest possible cost. 229 is often used in surface grinding where maximum cooling and minimum foam are desirable. 229 is also used in other situations including: water tables on plasma torches, leak detection dip tanks, abrasive cut off machines, and water jet cutting systems.
- Highly concentrated for very low-cost working solutions
- Will keep grinding wheels clean and the work piece cool
- Rapidly settles fines
- Nonfoaming, low mist and low odor working solutions
- Very low residue for easy cleaning
- Good ferrous corrosion inhibition without an oily film
- Rejects tramp oil for easy skimming and cleaning
- Easy recycling or disposal with conventional techniques and equipment
|
|
TRIM® 9106
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® 9106 is a clear, virtually odourless, synthetic coolant with excellent heat dissipating and corrosion inhibiting qualities. 9106 is recommended for grinding operations on cast iron, aluminum and steels. 9106 will not form ammonia when grinding cast iron. 9106 allows graphite to float, and prevents swarf from clinkering when grinding cast iron. 9106 contains no sulphur, phosphorus, chlorine or other halogens.
- Very operator, machine and environmentally friendly
- Moderate pH
- Contains no biocides, no oil, and no halogens
- Will not form ammonia or other gases when grinding or machining cast iron
- Inhibits chip packing and clinkering
- Operators like 9106’s very low odour, low foam, low mist, and water clear working solution
- Compatible with brass, aluminium, and lead serrations on magnetic grinding chucks
- Machines are easily washed off with coolant working solution to minimize the buildup of residues and chips
- Very low carryoff for extremely low fluid operating costs
- Easy recycling or disposal with conventional techniques and equipment
|
|
|
|
TRIM® C115 is a high-performance synthetic fluid for working cast iron and mild steels. State-of-the-art chemical technology provides excellent cooling and chip settling, good tramp oil rejection and machine cleanliness while leaving a protective film on the machine tool.
- Compatible with a very wide range of materials including cast iron, steels, plastics and composites
- Does an excellent job in most glass, ceramic, and composite grinding applications
- Excellent corrosion inhibition on most common ferrous and nonferrous alloys
- Extremely low carryoff keeps operating costs down
- Low foam and mist
- Very low initial odour level which usually disappears after one to two days
- Keeps your machines clean while leaving a soft, fluid film that protects bare metal parts
- Exceptional sump life and very good tramp oil rejection
|
|
TRIM® C117
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® C117 is a high-performance fully synthetic fluid for working cast iron and mild steels. State-of the-art technologies provide excellent cooling and chip settling, good tramp oil rejection and machine cleanliness while leaving a protective film on the machine tool.
- Compatible with a very wide range of materials including cast iron, steels, plastics and composites; and provides excellent corrosion inhibition on all ferrous alloys.
- Extremely low carry off for very low total operation costs.
- Very low foam and mist.
- Very low initial odour.
- Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts of your machine tools.
- Exceptional sump life and very good tramp oil rejection.
|
|
TRIM® C120 CG
Carbide Grinding Fluid
|
|
|
TRIM® C120CG was designed specifically for the carbide grinding industry. New features of this new product include low foam, superior sump life, low odor, and improved resistance to cobalt leaching. This fluid will not be stripped out by conventional filtration systems. C120CG is a synthetic product intended for grinding carbide as well as ceramics, cermets, chill cast alloys and tool steels.
FEATURES:
C120CG's formulation is based on modern MWF chemistry
- Minimizes cobalt leaching while maintaining superior cutting and noncutting characteristics
- Does not attack wheel bonding systems
- Rejects tramp oil and provides improved machine cleanliness
- Excellent operator acceptance due to very low product odor
- Excellent resistance to bacterial and fungal attack
Recommended working parameters:
- Concentration 5% - 6%
- pH - 8.6-8.8 range
C120 CG has a refractometer factor of 1.6.
Capable of being recycled with good tramp oil separation by conventional techniques.
C120CG is not classified as hazardous under the new CHIP 3 Regulations.
|
|
TRIM® C270
High Performance Synthetic
|
|
|
|
This product has Rolls Royce Approval CSS 130
TRIM® C270 is a chemical surface active or synthetic coolant concentrate designed to operate at very high fluid pressures and volumes with little or no foam. TRIM® C270 is ideally suited to situations where high coolant velocities or volumes are necessary to achieve maximum productivity. TRIM® C270 is designed to have the superior cooling and chip settling characteristics of a premium synthetic product with the improved residues and mechanical lubricity of a semi-synthetic coolant. This product utilises an extremely effective and proprietary non-chlorine, non-sulphur extreme pressure additive for good tool life and improved surface finishes
- Very stable formula provides long operational life with consistent performance.
- Chlorine and sulphur free extreme pressure (EP) additives control built-up edge (BUE).
- Excellent choice for nickel alloy, steel alloy and cast iron machining and grinding.
- Extremely low foam in mineral free water.
- Excellent tramp oil rejection.
- Water clear dilution aids filterability, reduces carryoff and facilitates getting the fluid to the point of cut.
- Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures.
- Easy recycling or disposal with conventional techniques and equipment.
- Contains no DEA, chlorine, nitrites or phenolic compounds
|
|
TRIM® C272
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® C272 is a chemical surface active or synthetic coolant concentrate designed to operate at very high fluid pressures and volumes with little or no foam. TRIM® C272 is ideally suited to situations where high coolant velocities or volumes are necessary to achieve maximum productivity. TRIM® C272 is designed to have the superior cooling and chip settling characteristics of a premium synthetic product with the improved residues and mechanical lubricity of a semi-synthetic coolant. This product utilises an extremely effective and proprietary non-chlorine, non-sulphur extreme pressure additive for good tool life and improved surface finishes
- Very stable formula provides long operational life with consistent performance.
- Chlorine and sulphur free extreme pressure (EP) additives control built-up edge (BUE).
- Excellent choice for nickel alloy, steel alloy and cast iron machining and grinding.
- Extremely low foam in mineral free water.
- Excellent tramp oil rejection.
- Water clear dilution aids filterability, reduces carryoff and facilitates getting the fluid to the point of cut.
- Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures.
- Easy recycling or disposal with conventional techniques and equipment.
- Contains no DEA, boron, chlorine, formaldehyde donors, nitrites or phenolic compounds
|
|
TRIM® C276
Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® C276 is a synthetic coolant that meets the needs of the most modern and demanding manufacturers. C276 makes use of the latest synthetic coolant formulation and specially synthesized oil to produce a versatile product that is clean running, has great sump life and is kind to both machines and operators. This product will perform well in centerless and cylindrical form grinding as well as on high-speed, single-point turning, and down-the-hole work on vertical and horizontal machining centers.
- Compatible with a very wide range of materials including cast iron, steels, copper alloys, plastics, and composites
- Very low foam and mist
- Provides excellent corrosion inhibition on all common ferrous and nonferrous alloys
- Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning
- Excellent extreme pressure (EP) lubricity to do many form grinding, drilling, tapping, and reaming operations without the need for chlorine or sulfur-based EP additives
- Extremely low carryoff for very low total operation costs
- Exceptional sump life and very good tramp oil rejection
- Very low initial odor level which usually disappears after one to two days
- Minimizes the build-up of sticky residues
|
|
TRIM® C320
Synthetic Cutting and Grinding Fluid Concentrate
|
|
|
TRIM® C320 is a low foam, high lubricity synthetic coolant that approaches the “down-the-hole” machining performance of premium soluble oils. TRIM® C320 is exceptionally good on aluminium. Even with its very high performance, TRIM®C320 meets or exceeds most stringent environmental standards.
- Excellent extreme pressure (EP) lubricity to do many drilling, tapping, reaming and form-grinding operations without chlorine or sulphur-based EP additives.
- A very versatile product which works well in mixed metal situations including aluminium, steels, cast iron and copper alloys.
- Provides good corrosion protection on all common ferrous and non-ferrous alloys.
- Keeps grinding wheels clean and sharp for higher “G ratios”, better surface integrity and faster stock removal.
- Contains no DEA, nitrites, phenolic compounds, “formaldehyde releasers” or chlorine.
- Operators like TRIM® C320’s low odour, low foam, low mist and water clear working solution.
- Keeps your machines clean while leaving a soft fluid film that protects bare metal parts
- Exceprional sump life, great resistance to bacteria and fungus and good tramp oil rejection.
- Coolant is easily removed with water, working solution or aqueous cleaners.
- TRIM® C320 is especially good for alumium wheel machining.
|
|
|
Aerospace
